Maine BMV CDL General Knowledge Practice Test 1
Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Maine test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age16 years
-
1. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
2. Cargo carried inside the cab must never do which of these?
Show answer
Answer C: Block the driver view, restrict arm or leg movement, or block an emergency exit
Anything inside the cab must leave the driver a clear view, free movement of the arms and legs, and an unobstructed way out of the vehicle.
-
3. How does a load carried high in the trailer affect safe speed through a curve?
Show answer
Answer B: It raises the rollover risk, so the speed must be lower
A high center of gravity lets the vehicle tip long before the tires lose their grip, so height of the load directly limits curve speed.
-
4. Which steering system findings count as defects during the inspection?
Show answer
Answer C: Bent, loose or broken column parts, arms, drag links or tie rods, and missing nuts, bolts or cotter keys
Every joint and fastener between the steering wheel and the tires carries the driver commands, so looseness or a missing retainer can end in a complete loss of steering.
-
5. On a one way street or a divided highway, where are the warning devices placed?
Show answer
Answer B: About 10 feet, 100 feet and 200 feet back toward the approaching traffic
When traffic can only come from one side, all three devices are spread out behind the vehicle to give approaching drivers a longer warning.
-
6. You are backing into a yard where electrical wires cross overhead. What is the main concern?
Show answer
Answer C: The wires may hang lower than the top of your vehicle
Overhead space has to be checked like any other space around the vehicle, because wires and cables are often lower than they look from the cab.
-
7. What minimum insurance does Maine require of a school bus carrying up to 30 passengers?
Show answer
Answer C: 500,000 dollars
Maine requires 500,000 dollars of coverage for a school bus with a capacity of up to 30 passengers, and 1,000,000 dollars for a larger one.
-
8. What tells you that an air suspension bag has a problem?
Show answer
Answer B: The bag is leaking or damaged, or the vehicle sits unevenly on that side
An air bag that leaks or is cut lets that corner of the vehicle settle, which throws the load onto the other suspension parts and changes the ride height.
-
9. While checking the in-cab gauges after start-up, what should the coolant temperature gauge do?
Show answer
Answer C: Rise gradually to the normal operating range
A healthy cooling system warms the engine slowly; a gauge that shoots up or stays cold points to a problem with the thermostat, coolant or sensor.
-
10. What is the best practice when fog is thick enough to hide the road ahead?
Show answer
Answer B: Slow down before entering the fog, and if visibility is too poor, pull off into a rest area or truck stop until it improves
The safest choice in heavy fog is not to be driving in it, and if you are already in it your speed has to come down before your visibility does.
-
11. You are about to cross a long, high bridge with a light load in gusty wind. What should you do?
Show answer
Answer C: Slow down and be ready for a sudden push
Wind is strongest where a bridge leaves the shelter of the land, and lower speed gives you time to correct when the first gust hits.
-
12. Why must the steering wheel be moved only a small amount at a time while backing?
Show answer
Answer B: Because a small turn of the wheel produces a large change at the rear of the vehicle
In reverse, the effect of the steering is greatly magnified at the back of the vehicle, so a small correction is usually all that is needed.
-
13. Loading heavy freight on top of lighter freight has what effect on the vehicle?
Show answer
Answer B: It raises the center of gravity and makes a rollover more likely
A high center of gravity lets the vehicle tip more easily in curves or during a sudden swerve.
-
14. Why does a load of live animals need special attention?
Show answer
Answer D: The animals move and lean, so the center of gravity shifts and the vehicle can be pushed off balance in a turn
A live load will not stay where it is put, and that movement changes the balance of the vehicle exactly when a curve is loading it most.
-
15. A brake light lens is cracked and the lamp still lights. How should that be treated?
Show answer
Answer B: As a defect, because water can enter and the lamp can dim or fail
A cracked lens lets in water and dirt, which corrodes the socket and dulls the lamp, so it is reported before it becomes a dead brake light.
-
16. What must the motor carrier do about a defect listed on a driver vehicle inspection report?
Show answer
Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again
A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.
-
17. What is the correct order for a basic double clutch upshift?
Show answer
Answer B: Release the accelerator and push the clutch, shift to neutral, release the clutch, let engine speed drop, push the clutch again and shift to the higher gear
Double clutching passes through neutral with the clutch released so engine speed can drop to match the next gear before it is engaged.
-
18. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?
Show answer
Answer A: Shift up as road speed rises, so engine braking falls away
An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.
-
19. Within what distance should high beams be lowered at night?
Show answer
Answer D: Within about 500 feet of an oncoming vehicle and within about 500 feet of a vehicle you are following
High beams blind other drivers at close range, so they are lowered at roughly the same distance whether the other vehicle is coming toward you or is ahead of you.
-
20. How much notice must a Maine applicant give the Bureau of Motor Vehicles to avoid an extra fee for a missed examination appointment?
Show answer
Answer B: 48 hours
Maine adds a fee when an applicant fails to keep an examination appointment unless the Bureau was notified at least 48 hours beforehand.
-
21. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
22. What should you look for on the electrical wiring in the engine compartment?
Show answer
Answer A: Worn, frayed or cracked insulation and loose or corroded connections
Damaged insulation can short a circuit against the frame or engine, which can kill a lamp you depend on or start a fire.
-
23. What must be checked on a sliding fifth wheel during the inspection?
Show answer
Answer B: That it is locked in position and not so far forward that the trailer can hit the cab
A slider that is unlocked can move under braking, and one set too far forward lets the trailer strike the cab when the tractor turns sharply.
-
24. Why must you never coast down a hill in neutral or with the clutch pushed in?
Show answer
Answer C: You lose the braking effect of the engine and your brakes may overheat and fail
Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.
-
25. At what time of day do drowsy driving crashes occur most often?
Show answer
Answer A: Between midnight and 6 a.m.
The body clock makes people sleepiest in the early morning hours, which is when most fatigue-related crashes happen.
-
26. Why is a leak in the exhaust system especially dangerous in cold weather?
Show answer
Answer A: Carbon monoxide can build up inside a closed cab
In winter the windows are shut and the heater is running, so exhaust gas that escapes early can reach the driver and cause drowsiness or worse.
-
27. A hard frost has left your vehicle covered in ice. What must be cleared before you drive?
Show answer
Answer D: The windshield, mirrors, lights and reflectors
You must be able to see out and other drivers must be able to see your lights and reflectors, so all of those surfaces have to be cleared.
-
28. Under federal rules, which commercial vehicles must stop at every railroad crossing before proceeding?
Show answer
Answer D: Passenger buses and placarded hazardous materials vehicles
Buses carrying passengers and vehicles required to display hazardous materials placards must stop at crossings, while other commercial vehicles slow and check.
-
29. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
30. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
31. What does mountain driving demand that flat country driving does not?
Show answer
Answer D: Lower gears and constant allowance for gravity
In the mountains gravity works for you on the climb and against you on the descent, so gear selection and speed control matter far more than on level road.
-
32. You are dropping a loaded trailer in a yard. How far should the landing gear be lowered?
Show answer
Answer A: Until the pads make firm contact and the trailer weight is just off the fifth wheel
Cranking down until the gear is firmly on the ground and just lifting the load off the fifth wheel makes the trailer stable and lets the tractor pull out cleanly.
-
33. What is the driver responsible for when a load is covered with a tarp?
Show answer
Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind
A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.
-
34. Cargo falls from your trailer and causes a crash behind you. Who is likely to answer for it?
Show answer
Answer C: The driver and the carrier, since securing the load on the road is their duty
Whoever loaded the vehicle, the driver and the carrier are responsible for the load being secure while it is on the road.
-
35. An article of cargo has been blocked so that it cannot move forward. How many tiedowns does the federal rule call for?
Show answer
Answer A: One tiedown for every 10 feet of article length, or any part of that
Blocking against forward movement lowers the requirement to one tiedown per 10 feet of length or fraction of 10 feet.
-
36. A fire has started in the vehicle. How should the extinguisher be used?
Show answer
Answer B: Stay as far back as the reach of the extinguisher allows, stand upwind, and aim at the base of the fire
Aiming at the base attacks what is actually burning, and staying upwind and well back protects the driver from heat, smoke and the flames themselves.
-
37. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.
-
38. You are pulling away from the curb after a delivery. Why is a mirror check needed first?
Show answer
Answer B: A cyclist or a vehicle may be coming up alongside you
Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.
-
39. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?
Show answer
Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel
Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.
-
40. How is the fluid level in an automatic transmission usually checked?
Show answer
Answer A: With the engine running, following the procedure in the operator manual
Most automatic transmissions are designed to be checked with the engine running, and the operator manual gives the exact conditions for that vehicle.
-
41. How should speed and gears be handled when approaching a curve?
Show answer
Answer A: Slow to a safe speed and downshift before entering the curve
Braking and shifting are completed before the curve so the vehicle is settled and can pull gently through it without upsetting the load.
-
42. Which lights should be used in fog, by day or by night?
Show answer
Answer A: Low beams and fog lights, together with the four-way flashers
High beam light bounces back off the water droplets and makes seeing worse, while low beams, fog lights and flashers help you see and help others see you.
-
43. Where is a dunnage bag used and how does it work?
Show answer
Answer D: Between pieces of cargo inside a van, where it is inflated to take up the gap
A dunnage bag is placed in the void between loads and inflated so the cargo is wedged and cannot move as the vehicle rolls and brakes.
-
44. Which vehicle requires a Maine Class A license?
Show answer
Answer B: A combination rated over 26,001 pounds when the towed unit is rated over 10,000 pounds
Maine's Class A covers a combination of vehicles rated at 26,001 pounds or more when the units being towed are rated above 10,000 pounds; a single heavy vehicle falls under Class B.
-
45. A sign before a long descent shows 6 percent. What does that number tell you?
Show answer
Answer A: How steep the grade ahead is
Percent grade is the drop in feet for every hundred feet of road, so the higher the number the faster speed will build and the lower the gear you need.
-
46. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
47. Which road users are hardest to see at night?
Show answer
Answer C: Pedestrians and cyclists in dark clothing
People on foot or on a bicycle carry no lights of their own in many cases, so they appear only when the headlights reach them.
-
48. When traction is poor, such as on packed snow, how should you speed up?
Show answer
Answer C: Very gradually, so the drive wheels do not spin
Gentle throttle keeps the drive wheels from breaking traction, because spinning wheels give up both grip and directional control.
-
49. What is the coupling device weight rating on a vehicle?
Show answer
Answer A: The most weight that the coupling on the vehicle is rated to pull
The coupling device rating is a limit on how much weight the coupling may tow, and it is one of the ratings that has to be respected when a combination is loaded.
-
50. How far ahead can a driver see with low beams and with high beams?
Show answer
Answer C: About 250 feet with low beams and about 350 to 500 feet with high beams
Low beams reach roughly 250 feet and high beams roughly 350 to 500 feet, and speed at night has to stay inside the distance the lights really show.