Maine BMV CDL General Knowledge Practice Test 2
Test 2 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Maine test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age16 years
-
1. Your brakes are starting to fade on a mountain downgrade and a sign shows an escape ramp one mile ahead. What should you do?
Show answer
Answer B: Plan to use the ramp instead of trying to reach the bottom
Fading brakes on a grade only get worse, and the ramp exists precisely so a driver does not have to gamble on the rest of the descent.
-
2. On the Interstate System, what are the federal maximums for a tandem axle group and for gross vehicle weight?
Show answer
Answer B: 34,000 pounds and 80,000 pounds
The federal Interstate limits allow 34,000 pounds on a tandem axle group and 80,000 pounds gross.
-
3. What vision standard must a Maine CDL applicant meet?
Show answer
Answer B: 20/40 acuity with the best eye and a field of vision of at least 110 degrees
Maine screens for 20/40 acuity with the best eye and a total field of vision of at least 110 degrees before issuing a commercial learner's permit.
-
4. After coupling, where should the fifth wheel release handle be?
Show answer
Answer A: In the locked position with the safety latch in place
The handle must be pushed in and latched, because a handle left out means the jaws can open and release the trailer while you are driving.
-
5. While you are driving, what should you do to catch a developing problem with the vehicle?
Show answer
Answer A: Check the gauges regularly and pay attention to unusual sounds, smells or vibrations
Inspection continues during the trip: gauges, mirrors and your senses can reveal a problem long before a warning light does.
-
6. Regular mirror checks during a long trip can reveal which developing problem?
Show answer
Answer D: Smoke coming from a tire or from a wheel
Overheating tires, wheel bearings and brakes usually show as smoke long before anything appears on the dash, and mirrors are where a driver sees it.
-
7. What information does an inspection decal on a commercial vehicle carry?
Show answer
Answer B: The date of the inspection, where the inspection report is kept, and information identifying the vehicle
The decal shows when the inspection was done, the name and address of the entity that holds the inspection report, and which vehicle it belongs to, so an officer can confirm the inspection at a glance.
-
8. Which items belong to the trailer part of the walkaround inspection?
Show answer
Answer D: Landing gear, doors, tires, wheels, lights, reflectors, frame and cargo securement
The trailer has its own running gear, lighting, structure and load, and all of it is the responsibility of the driver pulling it.
-
9. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?
Show answer
Answer B: Any bus carrying passengers
The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.
-
10. What combined single limit does Maine require of a vehicle carrying freight for hire wholly within the State?
Show answer
Answer A: 350,000 dollars
Maine sets a 350,000 dollar combined single limit for intrastate commercial freight operations, far above the minimum required of an ordinary private vehicle.
-
11. What makes a brake hose or air line a defect during the walkaround?
Show answer
Answer D: It is cracked, worn, kinked, or rubbing against another part
A chafed or cracked line can burst under pressure and take the braking on that circuit with it, so damage and rubbing points must be corrected.
-
12. What does gross vehicle weight mean, as opposed to gross vehicle weight rating?
Show answer
Answer B: The actual weight of the single vehicle plus everything it is carrying
Gross vehicle weight is what the vehicle actually weighs at that moment; the rating is the maximum the manufacturer allows it to weigh.
-
13. Under the federal hours of service rules, how long may a property-carrying driver drive after 10 consecutive hours off duty?
Show answer
Answer D: Up to 11 hours, and only within a 14 hour window that starts when the driver comes on duty
The federal limit is 11 hours of driving after 10 consecutive hours off duty, and all of that driving has to fall inside a 14 hour window.
-
14. What is the danger of letting engine speed climb past the top of the rated rpm range before you shift?
Show answer
Answer B: You can damage the engine, so the shift should be made before that point
Every engine has a rated operating range; running above it can cause serious engine damage, so the upshift belongs at the top of that range, not beyond it.
-
15. Your vehicle is stopped just past a hill or curve that hides it from approaching traffic. How should the warning devices be adjusted?
Show answer
Answer A: Move the rearmost device farther back, up to 500 feet, so drivers are warned before the obstruction
When a hill or curve blocks the view, the farthest device is moved back beyond the obstruction so approaching drivers see the warning in time.
-
16. Which description matches controlled braking during an emergency stop?
Show answer
Answer D: Apply the brakes as hard as you can without locking the wheels and keep steering movements small
Controlled braking keeps the wheels rolling just short of lockup, which gives the shortest stop while you keep the ability to steer.
-
17. Which winter preparation matters most for keeping the road in view?
Show answer
Answer D: Working wipers, washer fluid and a working defroster
Slush and road spray coat the windshield within minutes in winter, so wipers, washer fluid and the defroster are what keep any view at all.
-
18. How should a commercial driver treat the speed posted for a curve?
Show answer
Answer B: As a limit set for cars in good conditions, so a heavy or tall load calls for a lower speed
Posted curve speeds are based on passenger vehicles in good conditions, and a tall or heavy load can roll over well below that speed.
-
19. Why should the mirrors be checked repeatedly while you make a tight turn?
Show answer
Answer C: To watch the rear of the vehicle clear other vehicles and objects
In a long vehicle the rear wheels cut inside the path of the front wheels, so only the mirrors show whether the rear is clearing curbs, poles and other vehicles.
-
20. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
21. In a vehicle with a manual transmission, when should the clutch be pushed in during a normal stop?
Show answer
Answer A: Just before the engine would stall, when the vehicle is nearly stopped
Staying in gear until the last moment keeps engine braking and steady control, so the clutch goes down only when the engine is about to drop below idle.
-
22. Under the federal hours of service rules, when must a property-carrying driver take a 30 minute break?
Show answer
Answer C: After 8 cumulative hours of driving time
Driving is not allowed after 8 cumulative hours of driving time without at least a 30 consecutive minute interruption of driving.
-
23. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?
Show answer
Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic
Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.
-
24. The shipper hands you the placards for a load that needs them. Who puts them on the vehicle?
Show answer
Answer C: The driver, who must also make sure they are the correct ones and are readable
The shipper supplies the placards, but it is the driver who must place them on the vehicle and confirm that they match the load and can be read.
-
25. You are stopped in traffic on a steep upgrade behind another truck. How much space should you leave in front?
Show answer
Answer A: Enough that you can pull away without rolling back into the vehicle behind you
Room ahead lets you get moving smoothly on a grade instead of having to hold the vehicle perfectly still or roll back toward the traffic behind.
-
26. Under federal rules, what is required of a commercial driver who wants to use a mobile phone while driving?
Show answer
Answer B: The phone must be hands-free and started with no more than a single button press, and it must not be held
Federal rules ban texting and hand-held phone use while driving a commercial vehicle; reaching for, holding or dialing a phone is a violation.
-
27. Under Maine's license class statute, what does operating a school bus or a motorcycle require?
Show answer
Answer D: A special endorsement on the license
Maine's statute on classes says that operating a school bus or a motorcycle, other than an autocycle, requires a special endorsement rather than a second document.
-
28. What is required of the hooks, rails, rings and anchor points that tiedowns attach to?
Show answer
Answer A: They must be part of the vehicle and strong enough for the load being secured
A tiedown is only as strong as what it is hooked to, so anchor points must be proper vehicle fittings rated for the job.
-
29. A commercial driver is convicted of two serious traffic violations within three years. What is the result?
Show answer
Answer D: Disqualification for 60 days
Two serious traffic violations in a three year period bring a 60 day disqualification, and a third in the same period raises it to 120 days.
-
30. You are the first to arrive at a crash. What is the correct order of actions?
Show answer
Answer C: Protect the area, notify the authorities, care for the injured
Preventing a second crash comes first, because an unprotected scene puts the injured and the helpers in more danger than the original collision.
-
31. Which lamp must make the rear registration plate legible after dark?
Show answer
Answer C: A white lamp that lights the plate
A white license plate lamp is required so the plate can be read at night, and a burned out one is a defect like any other lamp.
-
32. What do the U-bolts on a leaf spring suspension do?
Show answer
Answer A: They clamp the spring assembly to the axle so it cannot move
U-bolts hold the spring pack tight against the axle, and a loose or broken U-bolt lets the axle slide out of place under load.
-
33. Where should a driver expect fog to form first?
Show answer
Answer D: In low ground, near water and in valleys
Cool moist air settles in low places, so fog patches appear in hollows, river valleys and near lakes before they appear anywhere else.
-
34. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?
Show answer
Answer A: 5 seconds
One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.
-
35. You are making a right turn and cannot complete it without swinging into the oncoming lane. An oncoming car is approaching. What should you do?
Show answer
Answer A: Wait and let the oncoming vehicle pass before completing the turn, and do not back up
The oncoming vehicle has the lane; backing up in traffic is dangerous, so hold your position and finish the turn once the way is clear.
-
36. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
37. Why should the radiator cap never be removed while the engine is hot?
Show answer
Answer A: The cooling system is under pressure and scalding coolant can be sprayed out
A hot cooling system holds pressurized coolant above its normal boiling point, so releasing the cap can throw boiling liquid and steam at whoever is holding it.
-
38. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?
Show answer
Answer C: Move weight off the drive axles and onto the trailer axles
Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.
-
39. A 40 foot straight truck and a 70 foot tractor-trailer make the same right turn. Which needs more room and why?
Show answer
Answer B: The tractor-trailer, because the longer the vehicle the farther inside the rear wheels track
Off-tracking grows with the distance between the front and rear axles, so the longer combination cuts the corner much more sharply and needs extra room.
-
40. What happens to braking performance if oil or grease reaches a brake lining?
Show answer
Answer B: That brake loses much of its effect and the vehicle can pull to one side
A contaminated lining cannot grip the drum, so that wheel contributes little braking and the vehicle pulls toward the side that is still working.
-
41. While double clutching, what goes wrong if you take too long between the two clutch movements?
Show answer
Answer A: Engine speed falls too far and the gear becomes hard or impossible to engage
Double clutching only works while engine speed and road speed still match; a slow shift lets rpm drop away and the gear will not go in.
-
42. What is the first step of the standard seven-step vehicle inspection?
Show answer
Answer C: A general overview of the vehicle, including the last inspection report
The routine opens with a walk-up overview of the vehicle and a review of the previous inspection report so known defects are addressed first.
-
43. The only way into a customer yard forces you to back toward the right, or blind, side of the vehicle. What should you do?
Show answer
Answer D: Use a helper and get out to check the path more often than you normally would
Blind side backing is allowed but far riskier, so it calls for a spotter you can see and for repeated checks of the path on foot.
-
44. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?
Show answer
Answer B: Make every steering, braking and speed change gradual
Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.
-
45. Why is a quick lane change particularly risky with a load of hanging meat or of livestock?
Show answer
Answer A: The load swings or leans and can keep pushing the trailer after you straighten out
A swinging or leaning load keeps moving after the vehicle has finished the maneuver, so its momentum acts on the trailer at the worst moment.
-
46. When a helper guides you while backing, what should be agreed on before you start?
Show answer
Answer D: A set of hand signals, especially the signal that means stop
The driver and helper must agree on signals in advance, above all the stop signal, because they usually cannot hear each other.
-
47. During the engine compartment check, which leaks are you looking for?
Show answer
Answer D: Fuel, coolant, engine oil, power steering fluid and battery fluid
Every fluid in the compartment matters, because a fuel leak is a fire risk and a loss of coolant, oil, steering fluid or electrolyte can disable the vehicle.
-
48. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
49. Part of your load stands high enough to hide a rear lamp or a reflector. What must be done?
Show answer
Answer B: The load must be moved or extra lamps fitted so the required lights can be seen
Required lamps and reflectors must remain visible; if the cargo blocks them, the load is rearranged or additional lamps are fitted so the vehicle can still be seen.
-
50. What is the minimum tread depth required in every major groove of a steering axle tire?
Show answer
Answer D: 4/32 inch
Federal rules set a higher tread minimum for front steering tires than for other positions because a steering tire failure is far harder to control.